×Draw CircleDraw EllipseDraw RectangleDraw PolygonDraw StarCreate Line - PolylineCreate ArcDraw BezierCreate Vector TextureCreate TextAuto Layout TextText SelectionConvert Text To CurvesText On A CurveTrace BitmapDimensions

Dimensions

This tool allows you to add a variety of dimensioning annotations to your vector drawing.

Note: Pressing the Space-bar re-opens the last vector creation form you used. This is very useful when using the Editing forms in between creating dimensions.

Unless specified separately below, the dimensions are created using these steps:

  1. Select the dimension type you wish to need: length; height; width; angle or the radius or diameter of an arc.
  2. In the 2D View, click with the left mouse button to set the points the dimension needs:
    For an Angle Dimension, the first point is the centre-point.
  3. Click where you need the arrow-tips to be.
  4. Click to set the location of the dimension-line.
  5. Click to set where the annotation text will appear.
Note: To undo that last click, press the Esc key.

Length Dimension

Use this to dimension a straight-line length in any orientation between two points.

Length Dimension Examples

The text preview box will snap to to the middle of the dimension line, unless a Shift key is held down while dragging.

Vertical / Horizontal Dimension

These two options also allow any two points to be selected, but the resulting dimension will be locked to indicate a vertical or horizontal distance (respectively) between the two points.

The text preview box will snap to to the middle of the dimension line, unless a Shift key is held down while dragging.

Vertical / Horizontal Dimension Examples

Angle Dimension

This option allows any arbitrary angle to be measured. The process is similar to creating a 3 point arc. First you must pick the center of an angle you wish to measure - typically a corner point. The next 2 points clicked will set the extents of the sweep you are measuring. The next Click will determine the dashed dimension line positioning and the final click will set the position of the text annotation.

Angle Dimension Examples

Arc Dimension

With this option selected you will only be able to select arc spans with the first click of dimension tool (Bezier curve spans are not supported). The second click will set the position of the dimension annotation, which will show the radius (or diameter) of the selected arc span.

Note:

Circles or arcs that are polygonized (from an imported file or from the Curve fit vectors command using Straight lines) are not recognized and cannot be dimensioned with this tool (which is in line with snapping which also won't work on polylines to see if they are circular). Circular Polylines can sometimes be dimensioned using the length dimensioning tools across their diameter.

The Fit Curves IconFit Curves to Vectors command may be useful to turn polylines or bezier curves into arcs.

The text in the following example was first converted to vectors using the Text To Curves IconConvert Text to Curves command, then those vectors were converted to arcs using the Fit Curves IconFit Curves to Vectors command:

Angle Dimension Examples

Further Angle Dimension Examples:

Further Angle Dimension Examples

Font Selection and Settings

This section of the form allows the user to change the settings for the dimension annotation, such as the font to be used, the height of the text and how many decimal places are required. The Offset field determines the gap left between the dimension markers and the vectors that are being measured.

Use Custom Text

You can check ✓ Use Custom Text to insert your own custom text. The text is stored per dimension, so you change between calculated and custom text without losing a dimension's custom text. When the form is first opened it defaults to calculated text.

Place Dimensions on Layer

By default this option is checked ✓ and the dimensions will be placed on a mid-gray Dimensions Layer. You can edit the name of the layer in the Name edit field. If a layer of this name does not exist, it will be created automatically.

Note: Dimensions can be edited. Hold shift while selecting the dimension you wish to edit or use the Undo shortcut Ctrl+Z to undo previously created Dimensions while still in the Dimensioning tool.

The base of extension lines and the tips of arrows are snap-points allowing you to keep neighbouring linear dimension lines, lined up, for example.